Measure the voltage of the local power grid, whether the output is stable above 220V or 110V (vary according to different country).ģ. If doesn’t solvethe problem, please try next step.Ģ.
Mcreator setup failed upgrade#
Download the latest version laserbox software and upgrade the latest firmware. Pause this printing task, the laserbox software prompts that the purifier is blockedġ. The air pressure of the purifier is too low （If still the same error Qx30 after replaced the Y1 board, please restart the machine） If doesn’t solve the problem, please try next step.ĥ. Disassemble the water level sensor to adjust the sensitivity (Reduce the sensitivity) or change the water level senser. If doesn’t solve the problem, please try next step.Ĥ. (Need disassemble the left shells of the machine). Check if there is red light on the water level sensor? If there is a red light, means the water level sensor is okay, otherwise, check if the cable connection of the water level sensor loose, please replug its cable on particular port of Y1 board. (Need disassemble the left shells of the machine)ģ. If doesn’t solve the problem, please try next step. Check the water level in the water tank, if it is really too low (under the water level line), need add some pure water. If doesn’t solve the problem, please try next step.Ģ. If doesn’t solve the problem, please try next step.ģ. (Need disassemble the right shells of the machine).
If there is no sound like “dada”, check if the cable connection of the air pump loose, please replug its cable on particular port of mainboard. If there is sound but no wind blowing, please check if it is blocked on the air inlet and air outlet, and try clean the air inlet and air outlet (Need disassemble the right shells of the machine)ī. If there is sound, please put your hand under the laser head and feel if there is wind blowing, if not, proceed to the next step.Ī. Enter the debug page by pressing the CTRL+F1 (Command + F1 for Mac), then open the air pump testing and listen carefully if there is sound like “dada” from the right hand side of the machine. Even if the peripheral is repaired, the machine must be restarted to restore the printing functionĢ. The printing task is terminated and the machine enters a fault state. If there is no other hardware failure, the machine exits the fault state and resumes the printing function The temperature of the water tank returns to normal. The temperature of the water tank is normal The temperature of water tank is too high Check if the cable connection of the water temperature sensor loose, please replug its cable on the paticular port of Y1 board. Check if the smoke purifier is placed very close to the laserbox machine and block the exhaust fan of the laserbox machine. Terminate the printing task and the machine enters a fault stateġ.
Mcreator setup failed code#
Hardware error Laserbox error code table Hardware Exception Report and Solution 101Įxample Using Hwi, Swi, and Task Threads. 88ģ.5.6 Task Yielding for Time-Slice Scheduling. 84ģ.5.2 Task Execution States and Scheduling. 71ģ.4.5 Using a Swi Object’s Trigger Variable. 70ģ.4.4 Execution of Software Interrupts. 69ģ.4.3 Software Interrupt Priorities and System Stack Size. 68ģ.4.2 Setting Software Interrupt Priorities. 60ģ.3.2 Hardware Interrupt Nesting and System Stack Size. 52ģ.2.3 A Comparison of Thread Characteristics.
52ģ.2.2 Choosing Which Types of Threads to Use. Ģ.3.4 Running and Debugging an Application in CCS. Ģ.3.2 Rules for Working with CCS Project Properties.Ģ.3.3 Building an Application with GCC. Ģ.2.8 Using the Problems View.Ģ.2.9 Finding and Fixing Errors.Ģ.2.10 Accessing the Global Namespace. Ģ.2.6 Using the Outline View.Ģ.2.7 Using the Property View.
Ģ.2.1 Opening a Configuration File with XGCONF. Ģ.1.4 Creating a Separate Configuration Project. Ģ.1.3 Adding SYS/BIOS Support to a Project. Ģ.1.2 Creating a SYS/BIOS Project with the New Project Wizard. Ģ.1.1 Creating a SYS/BIOS Project with the TI Resource Explorer. ġ.6.1 Using the API Reference Help System. ġ.5.3 Calling Class Methods from the Configuration.ġ.5.4 Class Constructors and Destructors. ġ.3.2 Configuring SYS/BIOS Using XDCtools. ġ.2 How is SYS/BIOS Different from DSP/BIOS?.ġ.3 How are SYS/BIOS and XDCtools Related?. TI SYS/BIOS v6.35 Real-time Operating System
0 kommentar(er)
